Dillon Quick-Check Wire Tension Meter (Red) Bedienungsanleitung

Quick Check “Red”Tension MeterUser InstructionsAWT35-501364Issue AA

10 Quick-Check Red User Instructions2 IntroductionThis manual covers the setup and operation of the Quick-Check Clamp Line Tensiometer from Dillon. T

Quick-Check Red User Instructions 11 2.2 Front Panel and KeysThe front panel of the Quick-Check is shown in Figure 2.2. The light located under the

12 Quick-Check Red User Instructions2.3 Important FeaturesQuick to use Attaches and removes from tensioned line in seconds. Quick-tensioning readout

Quick-Check Red User Instructions 13 2.4.2 External Power SupplyPlug the 4-pin end of the power supply cable into the Quick Check 4-pin connector lo

14 Quick-Check Red User Instructions3 OperationTypical operation of the Quick-Check is covered below, followed by explanations of the various display

Quick-Check Red User Instructions 15 4. Release the lever arm and you are ready to perform another measurement.Figure 3.2 Quick-Check Attached to C

16 Quick-Check Red User InstructionsInsure sheaves installed agree with sheaves noted in the Wire calibration. Exception: Sheaves match the wire diam

Quick-Check Red User Instructions 17 ModePress the Mode key to scroll through the four display modes. These are explained below:Live Tension Mode: T

18 Quick-Check Red User InstructionsStorePress the Store softkey to store and add a displayed tension to the average of other entered readings. Follo

Quick-Check Red User Instructions 19 Setup: Setup allows the user to configure how the Quick Check stores data internally. This stored data can be

quick check red_u_en_501364.bookDillon is part of Avery Weigh-Tronix. Avery Weigh-Tronix is a trademark of the Illinois Tool Works group of companies

20 Quick-Check Red User InstructionsComm Port:This allows you to choose where to export the "ON PRINT" logged data. a. Cell = Setup C

Quick-Check Red User Instructions 21 Comm Port:This allows you to choose where to export the "ON PRINT" logged data. a. Cell = Setup

22 Quick-Check Red User InstructionsThe data will be exported to a computer via RS-232. Dillon recommends using “WedgeLink” software as a keyboard we

Quick-Check Red User Instructions 23 SetupPress the Setup softkey and you will see these choices; Power, PtFmt, Misc, About, Test and Clock. These a

24 Quick-Check Red User Instructionsl Enable Auto-Shutdown - Auto-Shutdown powers off the instrument automatically. If Yes is chosen, the following o

Quick-Check Red User Instructions 25 About: Press this softkey to see the following information:l Device - Press this softkey to show a list of inf

26 Quick-Check Red User Instructions4 Configuration Mode4.1 Accessing the Configuration ModeYou need to access the Configuration mode to perform cert

Quick-Check Red User Instructions 27 4. The unit is now in the Configuration mode. To see the rest of the softkeys available in this mode, press the

28 Quick-Check Red User InstructionsCommCommunication output (COM1) and RADIO are not supported at this time in the Quick-Check. Press the COMM key t

Quick-Check Red User Instructions 29 l Fixed - The unit will shutdown after the set number of minutes no matter what happens.l No Load - The unit wi

Quick Check Red User Instructions 3 Table of ContentsChapter 1 General Information and Warnings ...

30 Quick-Check Red User Instructions5 Changing SheavesAs you use the Quick-Check on different diameter cables you must change to the correct sheave s

Quick-Check Red User Instructions 31 6 Achieving Best Accuracy6.1 AccuracyThe Quick-Check is an instrument designed to give accuracy that typically

32 Quick-Check Red User Instructions6.5 Non-linearityMost three-point tension meters employ only linear characterization and have large errors at the

Quick-Check Red User Instructions 33 7 Troubleshooting7.1 Quick CheckProblem Possible Cause SolutionPowers on momentarily and turns off Low battery

34 Quick-Check Red User Instructions7.2 EDX PSUProblem Possible Cause SolutionQuick Check powers on momentarily and turns offLow batteryBad keypadRep

Quick-Check Red User Instructions 35 8 SpecificationsPower2 AA, common alkaline batteries. DisplayDot graphic LCD displayOperational KeysPower, Wire

36 Quick-Check Red User InstructionsAvailable OptionsVaried wire sizesOperating EnvironmentSuitable for outdoor useDimensions10˝ x 23˝ x 3˝ (25 cm x

a division ofAvery Weigh-Tronix1000 Armstrong DriveFairmont, Minnesota U.S.A.Toll-Free: (800) 368-2031Phone: (507) 238-4461Fax: (507) 238-8258www.dill

4 Quick Check Red User Instructions

Quick-Check Red User Instructions 5 1 General Information and Warnings1.1 About this ManualThis manual is divided into chapters by the chapter numbe

6 Quick-Check Red User Instructions1.1.3 Safe Handling of Equipment with Batteries1.2 Routine Maintenance1.3 Cleaning the Machine1.4 TrainingDo not a

Quick-Check Red User Instructions 7 1.6 FCC and EMC Declarations of ComplianceUnited StatesCanadaEuropean CountriesThis equipment has been tested an

8 Quick-Check Red User Instructions1.7 Declaration of Conformity (Quick Check Red)

Quick-Check Red User Instructions 9 1.8 Declaration of Conformity (EDX PSU)